1. General description

The 74HC193-Q100; 74HCT193-Q100 is a 4-bit synchronous binary up/down counter. Separate

up/down clocks, CPU and CPD respectively, simplify operation. The outputs change state

synchronously with the LOW-to-HIGH transition of either clock input. If the CPU clock is pulsed

while CPD is held HIGH, the device counts up. If the CPD clock is pulsed while CPU is held

HIGH, the device counts down. Only one clock input can be held HIGH at any time to guarantee

predictable behavior. The device can be cleared at any time by the asynchronous master reset

input (MR). It may also be loaded in parallel by activating the asynchronous parallel load input (PL).

The terminal count up (TCU) and terminal count down (TCD) outputs are normally HIGH. When

the circuit has reached the maximum count state of 15, the next HIGH-to-LOW transition of CPU

causes TCU to go LOW. TCU remains LOW until CPU goes HIGH again, duplicating the count up

clock. Likewise, the TCD output goes LOW when the circuit is in the zero state and the CPD goes

LOW. The terminal count outputs duplicate the clock waveforms and can be used as the clock input

signals to the next higher-order circuit in a multistage counter. Multistage counters are not fully

synchronous, since there is a slight delay time difference added for each stage that is added. The

counter may be preset by the asynchronous parallel load capability of the circuit. Information on the

parallel data inputs (D0 to D3), is loaded into the counter. This information appears on the outputs

(Q0 to Q3) regardless of the conditions of the clock inputs when the parallel load (PL) input is LOW.

A HIGH level on the master reset (MR) input disables the parallel load gates. It overrides both clock

inputs and sets all outputs (Q0 to Q3) LOW. If one of the clock inputs is LOW during and after a

reset or load operation, the next LOW-to-HIGH transition of that clock is interpreted as a legitimate

signal and it is counted. Inputs include clamp diodes that enable the use of current limiting resistors

to interface inputs to voltages in excess of VCC.

This product has been qualified to the Automotive Electronics Council (AEC) standard Q100

(Grade 1) and is suitable for use in automotive applications.

2. Features and benefits

? Automotive product qualification in accordance with AEC-Q100 (Grade 1)

? Specified from -40 °C to +85 °C and from -40 °C to +125 °C

? Wide supply voltage range from 2.0 to 6.0 V

? CMOS low power dissipation

? High noise immunity

? Latch-up performance exceeds 100 mA per JESD 78 Class II Level B

? Input levels:

? For 74HC193-Q100: CMOS level

? For 74HCT193-Q100: TTL level

? Synchronous reversible 4-bit binary counting

? Asynchronous parallel load

? Asynchronous reset

? Expandable without external logic

? Complies with JEDEC standards:

? JESD8C (2.7 V to 3.6 V)

? JESD7A (2.0 V to 6.0 V)

74HC193D-Q100屬于集成電路（IC） > 計數器，除法器。安世半導體(中國)有限公司制造生產的74HC193D-Q100計數器，除法器計數器和除法器 IC 是數字邏輯器件，可對輸入發生的邏輯轉換進行計數，然后使用多個并行輸出重新發送累加的計數，和/或生成單個輸出信號轉換，從而對應用某些整數數量輸入信號轉換進行響應。除了簡單的事件計數，它們還可用于各種頻率合成應用。