Features

? AEC-Q100 qualified

? Full ISO26262 compliant, ASIL-D systems ready

? VDH motor supply voltage range from 4.5 V to 75 V for working in single

(12 V systems), double (24 V systems) and 48 V battery applications

? 3.3 V internal supply voltage generated from 5 V on VDD pin

? Digital I/O compatible to 3.3 V/5 V logics

? 6 separate N-channel FET pre-drivers:

– dedicated source connection to each FET

– the device can withstand -14 V to 95 V on motor connection pins

– 0 to 100 duty cycle operation support

– dedicated PWM input pin for each gate driver

? 3 differential high accuracy current monitors for ground referred current

measurements:

– ADC/DAC architecture

– SPI adjustable Gain Factor and Output Offset

– built-in error calibration

– the device can withstand -14 V to 6 V on input sensing pins

– SPI readable current measurement

– 0 to 4.6 V DAC output dynamic range

? 3 real time phase voltage monitor channels:

– SPI programmable phase voltage feedback;

– SPI readable phase duty cycle measurement;

? 32-bit - 10 MHz SPI interface with 5-bit CRC and 1bit frame counter for internal

setting, self-test and full diagnostics

? Protection and diagnostic:

– SPI programmable VDS diagnostic and protection in on-state

– SPI programmable Dead Time protection

– SPI programmable Shoot-through diagnostic and protection

– Open load, short to GND and short to battery diagnostic in off-state

– Over-temperature diagnostic and protection with SPI programmable

warning flag

– SPI readable Tj measurement

– Ground loss diagnostic

– System clock monitoring

– Power supply pins VDD, VDH, VBP over-voltage and under-voltage

diagnostic

– FET driver supply VPRE and VCP under-voltage and over-voltage

diagnostic

– SPI Window Watchdog

– Fault status flag output

Description

L9908 is a gate driver unit (GDU) for controlling 6 N-channel FETs for brushless

motors in automotive applications.

Each one of the 3 half bridge drivers channels (HS/LS couples) can be independently

configured allowing different load driving and is able to withstand -14 V to 95 V

excursion on motor`s pins.

Through 6 dedicated parallel inputs the pre-driver stages can be controlled

independently supporting duty cycle operations from 0 to 100 and allowing to

implement all kinds of electric motor control strategy. A dedicated combination of

regulators, charge pumps and bootstrap circuits allows L9908 to be suitable to

operate in passenger, commercial or hybrid vehicles.

Safe operation of half bridges is ensured by shoot-through diagnosis, dead-time,

short to battery, short to ground and open load detection plus a real time phase

voltage monitoring.

L9908 is equipped with 3 independent high accuracy current monitor channels

with SPI-configurable input differential voltage ranges for ground referenced current

measurements, with 5 V/3.3 V output dynamic range compatibility.

L9908 implements diagnostics on external and internal supply, ground level, internal

temperature.

A 32-bit out of frame SPI-slave interface is implemented for communication up to 10

MHz between L9908 and uC. SPI communication is safe-guarded by 5-bit CRC, 1bit

frame counter, frame length check and an SPI-configurable Window Watchdog.

Application

? EPS – Electronic Power Steering

? HVAC Blowers – Heating, ventilation, and air conditioning

? Engine Cooling Fans

? Electronic Brake Booster

? EWP, EFP, EOP

L9908屬于集成電路（IC） > 電機驅動器，控制器。意法半導體（ST）集團制造生產的L9908電機驅動器，控制器產品屬于電機驅動器和控制器電源管理集成電路 (PMIC) 系列，可用于控制或操作從某電源施加到電機或相關機電執行器的電源。所實現的具體功能和特性集根據預期負載和預期應用的特性有很大差異，范圍從用于有刷電機的簡單開環速度控制到基于步進電機的高級閉環運動控制。