EP7211-CV-A中文資料凌云邏輯數(shù)據(jù)手冊PDF規(guī)格書

OVERVIEW

The EP7211 is designed for ultra-low-power applications such as organizers/PDAs, two-way pagers, smart cellular phones, and industrial hand-held information appliances. The core-logic functionality of the device is built around an ARM720T processor with 8 kbytes of four-way set-associative unified cache and a write buffer. Incorporated into the ARM720T is an enhanced memory management unit (MMU), which allows for Microsoft Windows CE support.

FEATURES

■ Dynamically programmable clock speeds of 18, 36, 49, and 74 MHz at 2.5 V

■ Performance matching 100-MHz Intel? Pentium-based PC

■ Socket and register compatible with CL-PS7111

■ Ultra low power

— Designed for applications that require long battery life while using standard AA/AAA batteries or rechargeable cells

— 170 mW at 74 MHz in the Operating State

— 50 mW at 18 MHz in the Operating State

— 15 mW in the Idle State (clock to the CPU stopped, everything else running)

— 10 μW in the Standby State (realtime clock ‘on’, everything else stopped)

■ LCD controller

— Interfaces directly to a single-scan panel monochrome LCD

— Panel width size is programmable from 32 to 1024 pixels in 16-pixel increments

— Video frame buffer size programmable up to 128 kbytes

— Bits per pixel programmable from 1, 2, or 4

■ ARM720T processor

— ARM7TDMI CPU

— 8 kbytes of four-way set-associative cache

— MMU with 64-entry TLB (transition look aside buffer)

— Write buffer

— Windows CE enabled

— Thumb? code support enabled

■ DRAM controller

— Supports both 16- and 32-bit-wide DRAMs

— EDO support (fast page mode support for 13 MHz and 18 MHz operation only)

■ ROM/SRAM/FLASH memory control

— Decodes 4, 5, or 6 separate memory segments of up to 256 Mbytes each

— Each segment can be configured as 8, 16, or 32 bits wide and supports page-mode access

— Programmable access time for conventional ROM/SRAM/Flash memory

■ 37.5 kbytes of on-chip SRAM for fast program execution and/or as a frame buffer

■ On-chip ROM; for manufacturing boot-up support

■ Four synchronous serial interfaces

— ADC (SSI1) Interface: Master mode only; SPI?1 and Microwire1?2-compatible (128 kbps operation)

— SSI2 Interface: Master/Slave mode; SPI/Microwire2 compatible (512 kbps operation)

— Audio Codec Interface (64 kbps operation)

— Multimedia Codec Port (Interfaces to Philips’ UCB1100 and UCB1200 codecs) (9.216 Mbps operation)

■ 27 bits of general-purpose I/O

— Three 8-bit and one 3-bit GPIO port

— Supports scanning keyboard matrix

■ Two UARTs (16550 type)

— Supports bit rates up to 115.2 kbps

— Contains two 16-byte FIFOs for TX and RX

— UART1 supports modem control signals

■ SIR (up to 115.2 kbps) infrared encoder

— IrDA (Infrared Data Association) SIR protocol encoder can be optionally switched into TX and RX signals of UART1

■ PWM interface

— Provides two 96-kHz clock outputs with programmable duty ratio (from 1-in-16 to 15-in-16) that can be used to drive a DC-to-DC converter

■ Two timer counters

■ 208-pin LQFP or 256-ball PBGA packages

■ Evaluation kit available with BOM, schematics, sample code, and design database

■ Support for up to two ultra-low-power CL-PS6700 PC Card controllers

■ Dedicated LED flasher pin from RTC

■ Full JTAG boundary scan and Embedded ICE support