CC1312PSIPMOT中文資料德州儀器數據手冊PDF規(guī)格書

1 Features

Wireless microcontroller

? Powerful 48 MHz Arm? Cortex?-M4F processor

? 352KB flash program memory

? 256KB of ROM for protocols and library functions

? 8KB of cache SRAM

? 80KB of ultra-low leakage SRAM with parity for

high-reliability operation

? Programmable radio includes support for 2-

(G)FSK, 4-(G)FSK, MSK, OOK, IEEE 802.15.4

PHY and MAC

? Supports over-the-air upgrade (OTA)

Ultra-low power sensor controller

? Autonomous MCU with 4KB of SRAM

? Sample, store, and process sensor data

? Fast wake-up for low-power operation

? Software defined peripherals; capacitive touch,

flow meter, LCD

Low power consumption

? MCU consumption:

– 2.9 mA active mode, CoreMark?

– 60 μA/MHz running CoreMark?

– 0.9 μA standby mode, RTC, 80KB SRAM

– 0.1 μA shutdown mode, wake-up on pin

? Ultra low-power sensor controller consumption:

– 30 μA in 2 MHz mode

– 808 μA in 24 MHz mode

? Radio Consumption:

– 5.8 mA RX at 868 MHz

– 28.7 mA TX at +14 dBm at 868 MHz

– 62 mA TX at +19 dBm at 915 MHz

– 86 mA TX at +20 dBm at 915 MHz

Wireless protocol support

? Wi-SUN?

? mioty?

? Wireless M-Bus

? SimpleLink? TI 15.4-stack

? 6LoWPAN, Proprietary systems

High-performance radio

? –119 dBm for 2.5 kbps long-range mode

? –108 dBm at 50 kbps, 802.15.4, 868 MHz

? Output power up to +20 dBm with temperature and

voltage compensation

Regulatory compliance

? Certified module for:

– FCC CFR47 Part 15

– ISED Certified (Canada)

? Suitable for systems targeting compliance with:

– ETSI EN 300 220 Receiver Cat. 1.5 and 2, EN

303 131, EN 303 204

– ARIB STD-T108

MCU peripherals

? Digital peripherals can be routed to 30 GPIOs

? Four 32-bit or eight 16-bit general-purpose timers

? 12-bit ADC, 200 kSamples/s, 8 channels

? 8-bit DAC, two comparators

? Programmable current source

? Two UART, two SSI, I2C, I2S

? Real-time clock (RTC)

? Integrated temperature and battery monitor

Security enablers

? AES 128- and 256-bit cryptographic accelerator

? ECC and RSA public key hardware accelerator

? SHA2 Accelerator (full suite up to SHA-512)

? True random number generator (TRNG)

Development tools and software

? LP-CC1312PSIP Development Kit

? SimpleLink Low Power F2 SDK

? SmartRF? Studio for simple radio configuration

? Sensor Controller Studio for building low-power

sensing applications

? SysConfig system configuration tool

Operating range

? 1.8 V to 3.8 V single supply voltage

? –40 to +105°C (+14 dBm PA)

? –40 to +95°C (+20 dBm PA)

All necessary components integrated

? 48-MHz crystal: RF accuracy ±10 ppm initial and

over temperature

? 32-kHz crystal: RTC accuracy ±50 ppm initial and

over temperature

? DC/DC converter components and decoupling

? Single-RF pin for RX/TX with 50 Ohm impedance.

Package

? 7-mm × 7-mm MOT (30 GPIOs)

? Pin-to-pin compatible with CC2652RSIP and

CC2652PSIP

? RoHS-compliant package

2 Applications

? 868 and 902 to 928 MHz ISM and SRD systems 1

with down to 4 kHz of receive bandwidth

? Building automation

– Building security systems – motion detector,

electronic smart lock, door and window sensor,

garage door system, gateway

– HVAC – thermostat, wireless environmental

sensor, HVAC system controller, gateway

– Fire safety system – smoke and heat detector,

fire alarm control panel (FACP)

– Video surveillance – IP network camera

– Elevators and escalators – elevator main

control panel for elevators and escalators

? Grid infrastructure

– Smart meters – water meter, gas meter,

electricity meter, and heat cost allocators

– Grid communications – wireless

communications – long-range sensor

applications

– EV Charging infrastructure – AC charging (pile)

station

– Solar Energy - Micro inverter

– Other alternative energy – energy harvesting

? Industrial transport – asset tracking

? Factory automation and control

? Medical

? Communication equipment

– Wired networking – wireless LAN or Wi-Fi

access points, edge router

3 Description

The SimpleLink? CC1312PSIP device is an RF certified System-in-Package (SiP) Sub-1 GHz wireless

module supporting Wi-SUN?, Wireless M-Bus, IEEE 802.15.4, IPv6-enabled smart objects (6LoWPAN), mioty,

proprietary systems, including the TI 15.4-Stack. The CC1312PSIP microcontroller (MCU) is based on an Arm?

Cortex? M4F main processor and optimized for low-power wireless communication and advanced sensing in grid

infrastructure, building automation, retail automation and medical applications.

The CC1312PSIP has a low sleep current of 0.9 μA with RTC and 80KB RAM retention. In addition to the main

Cortex? M4F processor, the device also has an autonomous ultra-low power Sensor Controller CPU with fast

wake-up capability. As an example, the sensor controller is capable of 1-Hz ADC sampling at average 1-μA

system current.

The CC1312PSIP has Low SER (Soft Error Rate) FIT (Failure-in-time) for long operational lifetime. Always-on

SRAM parity minimizes risk for corruption due to potential radiation events. Consistent with many customers’ 10

to 15 years or longer life cycle requirements, TI has a product life cycle policy with a commitment to product

longevity and continuity of supply including dual sourcing of key components in the SIP.

The CC1312PSIP device is part of the SimpleLink? MCU platform, which consists of Wi-Fi?, Bluetooth? Low

Energy, Thread, Zigbee, Wi-SUN?, Amazon Sidewalk, mioty, Sub-1 GHz MCUs, and host MCUs. CC1312PSIP

is part of a portfolio that includes pin-compatible 2.4-GHz SIPs for easy adaption of a wireless product

to multiple communication standards. The common SimpleLink Low Power F2 SDK and SysConfig system

configuration tool supports migration between devices in the portfolio. A comprehensive number of software

stacks, application examples and SimpleLink? Academy training sessions are included in the SDK. For more

information, visit wireless connectivity.