1 Features

Processor Cores:

? Up to Quad 64-bit Arm? Cortex?-A53

microprocessor subsystem at up to 1.4 GHz

– Quad-core Cortex-A53 cluster with 512KB L2

shared cache with SECDED ECC

– Each A53 Core has 32KB L1 DCache with

SECDED ECC and 32KB L1 ICache with Parity

protection

? Single-core Arm? Cortex?-M4F MCU at up to 400

MHz

– 256KB SRAM with SECDED ECC

? Dedicated Device/Power Manager

Multimedia:

? Display subsystem

– Dual display support

– 1920x1080 @ 60fps for each display

– 1x 2048x1080 + 1x 1280x720

– Up to 165 MHz pixel clock support with

Independent PLL for each display

– OLDI/LVDS (4 lanes - 2x) and 24-bit RGB

parallel interface

– Support safety feature such as freeze frame

detection and MISR data check

? 3D Graphics Processing Unit

– 1 pixel per clock or higher

– Fillrate greater than 500 Mpixels/sec

– >500 MTexels/s, >8 GFLOPs

– Supports at least 2 composition layers

– Supports up to 2048x1080 @60fps

– Supports ARGB32, RGB565 and YUV formats

– 2D graphics capable

– OpenGL ES 3.1, Vulkan 1.2

? One Camera Serial interface (CSI-Rx) - 4 Lane

with DPHY

– MIPI CSI 1.3 Compliant + MIPI-DPHY 1.2

– Support for 1,2,3 or 4 data lane mode up to

2.5Gbps

– ECC verification/correction with CRC check +

ECC on RAM

– Virtual Channel support (up to 16)

– Ability to write stream data directly to DDR via

DMA

Memory Subsystem:

? Up to 816KB of On-chip RAM

– 64KB of On-chip RAM (OCSRAM) with

SECDED ECC , Can be divided into smaller

banks in increments of 32KB for as many as 2

separate memory banks

– 256KB of On-chip RAM with SECDED ECC in

SMS Subsystem

– 176KB of On-chip RAM with SECDED ECC in

SMS Subsystem for TI security firmware

– 256KB of On-chip RAM with SECDED ECC in

Cortex-M4F MCU subsystem

– 64KB of On-chip RAM with SECDED ECC in

Device/Power Manager Subsystem

? DDR Subsystem (DDRSS)

– Supports LPDDR4, DDR4 memory types

– 16-Bit data bus with inline ECC

– Supports speeds up to 1600 MT/s

– Max addressable range

? 8GBytes with DDR4

? 4GBytes with LPDDR4

Functional Safety:

? Functional Safety-Compliant targeted [Industrial]

– Developed for functional safety applications

– Documentation will be available to aid IEC

61508 functional safety system design

– Systematic capability up to SIL 3 targeted

– Hardware Integrity up to SIL 2 targeted

– Safety-related certification

? IEC 61508 by TUV SUD planned

? Functional Safety-Compliant targeted [Automotive]

– Developed for functional safety applications

– Documentation will be available to aid ISO

26262 functional safety system design

– Systematic capability up to ASIL D targeted

– Hardware integrity up to ASIL B targeted

– Safety-related certification

? ISO 26262 by TUV SUD planned

? AEC-Q100 qualified

Security:

? Hardware Security Module

– Dedicated dual-core Arm Cortex-M4F Security

co-processor with 426KB RAM for key and

security management, with dedicated device

level interconnect for security

– Dedicated security DMA and IPC subsystem for

isolated processing

? Secure boot supported

– Hardware-enforced Root-of-Trust (RoT)

– Support to switch RoT via backup key

– Support for takeover protection, IP protection,

and anti-roll back protection

? Cryptographic acceleration supported

– Session-aware cryptographic engine with ability

to auto-switch key-material based on incoming

data stream

– Supports cryptographic cores

? AES – 128/192/256 Bits key sizes

? SHA2 – 224/256/384/512

? DRBG with true random number generator

? PKA (Public Key Accelerator) to Assist in

RSA/ECC processing

– DMA support

? Debugging security

– Secure software controlled debug access

– Security aware debugging

? Trusted Execution Environment (TEE) supported

– Arm TrustZone? based TEE

– Extensive firewall support for isolation

– Secure watchdog/timer/IPC

? Secure storage support

? On-the-Fly encryption support for OSPI interface in

XIP mode

PRU Subsystem:

? Dual-core Programmable Real-Time Unit

Subystem (PRUSS) running up to 333 MHz

? Intended for driving GPIO for cycle accurate

protocols such as additional:

– General Purpose Input/Output (GPIO)

– UARTs

– I2C

– External ADC

? 16KByte program memory per PRU with SECDED

ECC

? 8KB data memory per PRU with SECDED ECC

? 32KB general purpose memory with SECDED

ECC

? CRC32/16 HW accelerator

? Scratch PAD memory with 3 banks of 30 x 32-bit

registers

? 1 Industrial 64-bit timer with 9 capture and

16 compare events, along with slow and fast

compensation

? 1 interrupt controller (INTC), minimum of 64 input

events supported

High-Speed Interfaces:

? Integrated Ethernet switch supporting (total 2

external ports)

– RMII(10/100) or RGMII (10/100/1000)

– IEEE1588 (Annex D, Annex E, Annex F with

802.1AS PTP)

– Clause 45 MDIO PHY management

– Packet Classifier based on ALE engine with

512 classifiers

– Priority based flow control

– Time sensitive networking (TSN) support

– Four CPU H/W interrupt Pacing

– IP/UDP/TCP checksum offload in hardware

? Two USB2.0 Ports

– Port configurable as USB host, USB peripheral,

or USB Dual-Role Device (DRD mode)

– Integrated USB VBUS detection

– Trace over USB supported

General Connectivity:

? 9x Universal Asynchronous Receiver-Transmitters

(UART)

? 5x Serial Peripheral Interface (SPI) controllers

? 6x Inter-Integrated Circuit (I2C) ports

? 3x Multichannel Audio Serial Ports (McASP)

– Transmit and Receive Clocks up to 50 MHz

– Up to 16/10/6 Serial Data Pins across 3x

McASP with Independent TX and RX Clocks

– Supports Time Division Multiplexing (TDM),

Inter-IC Sound (I2S), and Similar Formats

– Supports Digital Audio Interface Transmission

(SPDIF, IEC60958-1, and AES-3 Formats)

– FIFO Buffers for Transmit and Receive (256

Bytes)

– Support for audio reference output clock

? 3x enhanced PWM modules (ePWM)

? 3x enhanced Quadrature Encoder Pulse modules

(eQEP)

? 3x enhanced Capture modules (eCAP)

? General-Purpose I/O (GPIO), All LVCMOS I/O can

be configured as GPIO

? 3x Controller Area Network (CAN) modules with

CAN-FD support

– Conforms w/ CAN Protocol 2.0 A, B and ISO

11898-1

– Full CAN FD support (up to 64 data bytes)

– Parity/ECC check for Message RAM

– Speed up to 8Mbps

Media and Data Storage:

? 3x Secure Digital? (SD?) (4b+4b+8b) interface

– 1x 8-bit eMMC interface up to HS200 speed

– 2x 4-bit SD/SDIO interface up to UHS-I

– Compliant with eMMC 5.1, SD 3.0 and SDIO

Version 3.0

? 1× General-Purpose Memory Controller (GPMC)

up to 133 MHz

– Flexible 8- and 16-Bit Asynchronous Memory

Interface With up to four Chip (22-bit address)

Selects (NAND, NOR, Muxed-NOR, and

SRAM)

– Uses BCH Code to Support 4-, 8-, or 16-Bit

ECC

– Uses Hamming Code to Support 1-Bit ECC

– Error Locator Module (ELM)

? Used With the GPMC to Locate Addresses

of Data Errors From Syndrome Polynomials

Generated Using a BCH Algorithm

? Supports 4-, 8-, and 16-Bit Per 512-Byte

Block Error Location Based on BCH

Algorithms

? OSPI/QSPI with DDR / SDR support

– Support for Serial NAND and Serial NOR flash

devices

– 4GBytes memory address support

– XIP mode with optional on-the-fly encryption

Power Management:

? Low power modes supported by Device/Power

Manager

– Partial IO support for CAN/GPIO/UART wakeup

– DeepSleep

– MCU Only

– Standby

– Dynamic frequency scaling for Cortex-A53

Optimal Power Management Solution:

? Recommended TPS65219 Power Management

ICs (PMIC)

– Companion PMIC specially designed to meet

device power supply requirements

– Flexible mapping and factory programmed

configurations to support different use cases

Boot Options:

? UART

? I2C EEPROM

? OSPI/QSPI Flash

? GPMC NOR/NAND Flash

? Serial NAND Flash

? SD Card

? eMMC

? USB (host) boot from Mass Storage device

? USB (device) boot from external host (DFU mode)

? Ethernet

Technology / Package:

? 16-nm technology

? 13 mm x 13 mm, 0.5-mm pitch, 425-pin FCCSP

BGA (ALW)

? 17.2 mm x 17.2 mm, 0.8-mm pitch, 441-pin

FCBGA (AMC) [Advance Information]