GENERAL DESCRIPTION

The AD7622 is a 16-bit, 2 MSPS, charge redistribution SAR, fully differential, analog-to-digital converter (ADC) that operates from a single 2.5 V power supply. The part contains a high speed, 16-bit sampling ADC, an internal conversion clock, an internal reference (and buffer), error correction circuits, and both serial and parallel system interface ports. It features two very high sampling rate modes (wideband warp and warp) and a fast mode (normal) for asynchronous rate applications. The AD7622 is hardware factory calibrated and tested to ensure ac parameters, such as signal-to-noise ratio (SNR), in addition to the more traditional dc parameters of gain, offset, and linearity. The AD7622 is available in Pb-free only packages with operation specified from ?40°C to +85°C.

FEATURES

Throughput

2 MSPS (wideband warp and warp mode)

1.5 MSPS (normal mode)

INL: ±0.5 LSB typical, ±1.5 LSB maximum (±23 ppm of FSR)

16-bit resolution with no missing codes

Dynamic range: 92.5 dB typical

SINAD: 91 dB minimum @ 20 kHz (VREF = 2.5 V)

THD: ?115 dB typical @ 20 kHz (VREF = 2.5 V)

2.048 V internal reference: typical drift 8 ppm/°C; TEMP output

Differential input range: ±VREF (VREF up to 2.5 V)

No pipeline delay (SAR architecture)

Parallel (16-, or 8-bit bus) and serial 5 V/3.3 V/2.5 V interface

SPI?/QSPI?/MICROWIRE?/DSP compatible

Single 2.5 V supply operation

Power dissipation

70 mW typical @ 2 MSPS with internal REF

2 μW in power-down mode

Pb-free, 48-lead LQFP and 48-lead LFCSP

Pin compatible with other PulSAR 48-lead ADCs

APPLICATIONS

Medical instruments

High speed data acquisition/high dynamic data acquisition

Digital signal processing

Spectrum analysis

Instrumentation

Communications

ATE

AD7622BCPZRL屬于集成電路（IC） > 模數轉換器（ADC）。亞德諾半導體技術有限公司制造生產的AD7622BCPZRL模數轉換器（ADC）模數轉換器（ADC、A/D 或 A 轉 D）對模擬信號進行采樣，例如由麥克風采集的聲音或傳感器的輸出，然后將其轉換為數字信號。一般來說，數字輸出是二進制補碼二進制數，與輸入成比例。輸入類型可能是差分、偽差分或單端輸入。模數轉換器可按照位數、采樣率、輸入數、接口、轉換器數和架構（例如自適應增量、雙斜率、折疊、流水線、SAR、三角積分、兩步式）進行選擇。